Archive: Service Bulletins - Vendors

403. 3D Vis Sign Installation on RVV Gen II

SUBJECT: 3D Vis Sign Installation on RVV Gen II REVISION: 00 MODELS: KO RVV 500 Gen II PURPOSE: This bulletin describes the process for installing a Coca-Cola 3D Vis-style sign on RVV Gen II. Download PDF: Service Bulletin 403 … [Read more...]

402. Malformed GIII Adjustable Long Product Stops

SUBJECT: Malformed GIII Adjustable Long Product Stops REVISION: 00 MODELS: GIII Plus venders BACKGROUND INFORMATION: Some GIII Plus venders manufactured from production weeks 201544 to 201605 may have malformed long adjustable product stops. It is important to note that a majority of the product stops during this time period are formed correctly; the issue with malformed parts is … [Read more...]

401. Coin Deflector Kit Installation

SUBJECT: Coin Deflector Kit Installation REVISION: 00 MODELS: GIII venders with Center Door Changer PURPOSE OF THIS BULLETIN: This bulletin describes the procedure for installing the coin deflector kit in GIII venders with Center Door Changers. Download PDF: Service Bulletin 401 … [Read more...]

399. Reinforced T-handle Lock Cylinder Cover Kit Installation

SUBJECT: Reinforced T-handle Lock Cylinder Cover Kit Installation REVISION: 00 MODELS: All ADA venders and GIII Marketing PURPOSE OF THIS BULLETIN: The reinforced T-handle lock cylinder cover blocks off the T-handle to prevent access to the latch cylinder by vandals. Download PDF: Service Bulletin 399 … [Read more...]

398. 20 oz Anti-bridging Kit for Merlin IV

SUBJECT: 20 oz Anti-bridging Kit for Merlin IV REVISION: 00 MODELS: 72" Merlin IV (models 650 and 542) PURPOSE OF THIS BULLETIN: In certain vintages of Merlin IV venders, bridging may occur with some 20 ounce bottles. In the event this occurs, this anti-bridging kit should alleviate the issue. Download PDF: Service Bulletin 398 … [Read more...]

395. LED Conversion Kit Installation in GIII Plus Venders

SUBJECT: LED Conversion Kit Installation in GIII Plus Venders REVISION: 03 MODELS: GIII Plus INTRODUCTION: This bulletin explains the procedure for converting GIII Plus venders built with T8 fluorescent lighting to a newer 24-volt LED lighting system. Download PDF: Service Bulletin 395 … [Read more...]

391. Clear Board Cover Installation on GIII Venders

SUBJECT: Clear Board Cover Installation on GIII Venders REVISION: 00 MODELS: GIII, GIII Plus BACKGROUND: A new clear board cover has been designed for use in GIII and GIII Plus venders to replace the black Kydex® cover that was previously used. Download PDF: Service Bulletin 391 … [Read more...]

394. Vend Motor Harness Clip Installation

SUBJECT: Vend Motor Harness Clip Installation REVISION: 00 MODELS: KO Merlin BACKGROUND: Some KO Merlin venders were produced without P-clips to secure the vend motor harness. On these venders, it is possible for the product chute to scrape the harness, which can cut through the outer insulation of the harness over time and cause it to fail. This bulletin explains the procedure for … [Read more...]

392. GIII Control Board Troubleshooting

SUBJECT: GIII Control Board Troubleshooting REVISION: 00 MODELS: All GIII models BACKGROUND: This job aid guides you through the steps to troubleshoot a vender's main controller board, including power supply, refrigeration, chute sensor, multi-drop bus (MDB), etc. Download PDF: Service Bulletin 392 … [Read more...]

390. New Logic Board and Cup Sensor Installation

SUBJECT: New Logic Board and Cup Sensor Installation REVISION: 00 MODELS: RVV NG REASON FOR BULLETIN: The infrared emitter that is part of the cup sensor emitter board on RVV NG venders produced before serial numbers beginning 201427PA is no longer produced. Therefore, a new emitter is in use on current-production boards, which renders these new boards incompatible with older infrared … [Read more...]